From 6e9c7aad1496109899902dad493808ec00982904 Mon Sep 17 00:00:00 2001 From: Andrey Skvortsov Date: Fri, 5 Jan 2024 13:40:33 +0300 Subject: [PATCH] sunxi: pinephone: detect existed magnetometer and fixup dtb In newer 1.2 PinePhone board revisions LIS3MDL magnetometer was replaced by AF8133J. They use the same PB1 pin in different modes. LIS3MDL uses it as an gpio input to handle interrupt. AF8133J uses it as an gpio output as a reset signal. It wasn't possible at runtime to enable both device tree nodes and detect supported sensor at probe time. AF8133J has reset pin (PB1) connected to the SoC. By default AF8133J is in a reset state and don't respond to probe request on I2C bus. Extra code would be needed to handle reset signal. Therefore this code uses LIS3MDL magnetometer instead of AF8133J. Introducing new dts 1.2b with AF8133J sensor would require probing in SPL. That would lead to pulling in into SPL I2C controller driver, RSB controller driver, introducing new AXP803 driver to power-up sensors for probe. It's working, but SPL is pretty size-constrained on A64 and doesn't have much space. Therefore fdt fixup is done in U-Boot proper without introducing new board revision and new dts. Signed-off-by: Andrey Skvortsov --- board/sunxi/board.c | 23 +++++++++++++++++++++++ configs/pinephone_defconfig | 1 + 2 files changed, 24 insertions(+) diff --git a/board/sunxi/board.c b/board/sunxi/board.c index 1305302060b..2f540f14790 100644 --- a/board/sunxi/board.c +++ b/board/sunxi/board.c @@ -15,6 +15,7 @@ #include #include #include +#include #include #include #include @@ -920,6 +921,27 @@ static void bluetooth_dt_fixup(void *blob) "local-bd-address", bdaddr, ETH_ALEN, 1); } +#define PINEPHONE_LIS3MDL_I2C_ADDR 0x1E +#define PINEPHONE_LIS3MDL_I2C_BUS 1 /* I2C1 */ + +static void board_dt_fixup(void *blob) +{ + struct udevice *bus, *dev; + + if (IS_ENABLED(CONFIG_PINEPHONE_DT_SELECTION) && + !fdt_node_check_compatible(blob, 0, "pine64,pinephone-1.2")) { + if (!uclass_get_device_by_seq(UCLASS_I2C, PINEPHONE_LIS3MDL_I2C_BUS, &bus)) { + dm_i2c_probe(bus, PINEPHONE_LIS3MDL_I2C_ADDR, 0, &dev); + fdt_set_status_by_compatible( + blob, "st,lis3mdl-magn", + dev ? FDT_STATUS_OKAY : FDT_STATUS_DISABLED); + fdt_set_status_by_compatible( + blob, "voltafield,af8133j", + dev ? FDT_STATUS_DISABLED : FDT_STATUS_OKAY); + } + } +} + int ft_board_setup(void *blob, struct bd_info *bd) { int __maybe_unused r; @@ -933,6 +955,7 @@ int ft_board_setup(void *blob, struct bd_info *bd) fdt_fixup_ethernet(blob); bluetooth_dt_fixup(blob); + board_dt_fixup(blob); #ifdef CONFIG_VIDEO_DT_SIMPLEFB r = sunxi_simplefb_setup(blob); diff --git a/configs/pinephone_defconfig b/configs/pinephone_defconfig index eebc6769015..457e7ee1e75 100644 --- a/configs/pinephone_defconfig +++ b/configs/pinephone_defconfig @@ -12,6 +12,7 @@ CONFIG_MMC_SUNXI_SLOT_EXTRA=2 CONFIG_PINEPHONE_DT_SELECTION=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_OF_LIST="sun50i-a64-pinephone-1.1 sun50i-a64-pinephone-1.2" +CONFIG_SYS_I2C_MVTWSI=y CONFIG_LED_STATUS=y CONFIG_LED_STATUS_GPIO=y CONFIG_LED_STATUS0=y