Skip to content

Latest commit

 

History

History
101 lines (65 loc) · 4.68 KB

README.md

File metadata and controls

101 lines (65 loc) · 4.68 KB
Raw

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.

Overview

This is a remix of DIY Machine's 3D printable BB8 robot.

It replaces the stock Arduino Uno with an ESP32 DevKit and includes a reed switch to turn the robot on/off. In addition, a generic L298N motor controller board replaces the original motor shield

Bill Of Materials

Qty. Name Link
10 6 * 3mm Neodymium magnets Amazon
1 Styrofoam hemisphere
1 Reed switch
1 L298N motor controller board
1 3.3V Low-dropout regulator board
1 DOIT ESP32 DevKit v1
1 4*AA Battery harness
2 Geared 6v motors Amazon
2 2.75in wheels (included with motors)
2-4 .25in 4-40 Machine screws
1 Can of white spray paint
1-2 fl oz White acrylic paint
Assorted sharpies
1 Roll of clear gift wrap tape
≥5 Small zipties
~1in2 Low friction PTFE tape
A few Male-male wires
A few Female-female wires
One of each Printed parts CAD/STLs

Assembly

Step 0: Prepping shells and decoration

  1. Sand the inside and outside of the shells so that the chassis and head can both slide freely on them

  2. Spray paint the outside of the shells

  3. Hotglue the styrofoam hemisphere to the head, then use white acrylic paint to coat the assembly

  4. Use the stand as a stencil to sharpie BB8 patterns onto the shell

Step 1: Installing motors and motor controller

  1. As shown in DIY Machines' video, put the motors in the chassis and secure them with zip ties

  2. Ziptie the motor controller bracket to the neck/mast of the chassis

  3. Use the screws to secure the motor controller with the heatsink facing down

Step 2: Installing the reed switch

  1. Use the jaws of a pair of calipers to gently bend the leads of the reed switch

    • Make sure the side with the circle artifacts from the injection mold is facing away from the leads

  2. Solder a pair of wires (any color, preferably red) to the leads

    • They should be about 4 inches long, better to make it long and cut later

  3. Insert the reed switch into the slot on the top of the neck/mast. Be careful not to bend the leads, lest you risk breaking the fragile reeds inside

Step 3: Wiring and cable management

  1. Connect the components according to the wiring diagram

    • To connect multiple wires to the screw terminals on the motor controller, strip the ends of the wires and twist them together
    • The GND pin of the LDO needs to be connected directly to the GND pin on the ESP32 board
      • If negative from the battery, GND on the LDO, and GND on the ESP32 are connected with separate wires to the GND terminal of the motor controller, then electrical noise causes the ESP32 to intermittently shut off, which is bad (duh)
      • To solve that issue, strip the opposite end of the wire that is connected to the ESP32's ground pin and (gently) shove that end into the connector on the LDO's ground pin, then put that connector back on the LDO pin

  2. Use a ziptie to secure the ESP32 board to the chassis TODO: example photo

  3. Do your best to round up all the cables so that none touch the wheels or shell of the robot

Wiring Diagram Source for the above image

Step 4: Installing neck and head magnets

  1. Glue (try superglue if possible) two magnets in each slot on top of the neck

    • Make sure that they are all in the same orientation

  2. Place small squares of PTFE tape on each exposed magnet

  3. Put a half of the shell on top of the neck, then put a piece of wax paper

  4. Stick three magnets to the ones in the neck (through the shell)

  5. Apply hot glue to those magnets, then quickly, before the glue cools, place the head as straight as possible, facing forward

  6. Once the magnets on the head are securely in place, glue another one in between the two in the front of the head

    • This is to trigger the reed switch when the head is in place

  7. After the glue has fully cooled, place small squares of PTFE tape on each exposed magnet

Step 5: Flash ESP32 board

  • See /Code/README.md