ISR_RPM_Measure.ino

/****************************************************************************************************************************
  ISR_RPM_Measure.ino
  For SAMD boards
  Written by Khoi Hoang

  Built by Khoi Hoang https://github.com/khoih-prog/SAMD_TimerInterrupt
  Licensed under MIT license

  Now even you use all these new 16 ISR-based timers,with their maximum interval practically unlimited (limited only by
  unsigned long miliseconds), you just consume only one SAMD timer and avoid conflicting with other cores' tasks.
  The accuracy is nearly perfect compared to software timers. The most important feature is they're ISR-based timers
  Therefore, their executions are not blocked by bad-behaving functions / tasks.
  This important feature is absolutely necessary for mission-critical tasks.
*****************************************************************************************************************************/
/*
   Notes:
   Special design is necessary to share data between interrupt code and the rest of your program.
   Variables usually need to be "volatile" types. Volatile tells the compiler to avoid optimizations that assume
   variable can not spontaneously change. Because your function may change variables while your program is using them,
   the compiler needs this hint. But volatile alone is often not enough.
   When accessing shared variables, usually interrupts must be disabled. Even with volatile,
   if the interrupt changes a multi-byte variable between a sequence of instructions, it can be read incorrectly.
   If your data is multiple variables, such as an array and a count, usually interrupts need to be disabled
   or the entire sequence of your code which accesses the data.

   RPM Measuring uses high frequency hardware timer 1Hz == 1ms) to measure the time from of one rotation, in ms
   then convert to RPM. One rotation is detected by reading the state of a magnetic REED SW or IR LED Sensor
   Asssuming LOW is active.
   For example: Max speed is 600RPM => 10 RPS => minimum 100ms a rotation. We'll use 80ms for debouncing
   If the time between active state is less than 8ms => consider noise.
   RPM = 60000 / (rotation time in ms)

   We use interrupt to detect whenever the SW is active, set a flag
   then use timer to count the time between active state
*/

#if !( defined(ARDUINO_SAMD_ZERO) || defined(ARDUINO_SAMD_MKR1000) || defined(ARDUINO_SAMD_MKRWIFI1010) \
      || defined(ARDUINO_SAMD_NANO_33_IOT) || defined(ARDUINO_SAMD_MKRFox1200) || defined(ARDUINO_SAMD_MKRWAN1300) || defined(ARDUINO_SAMD_MKRWAN1310) \
      || defined(ARDUINO_SAMD_MKRGSM1400) || defined(ARDUINO_SAMD_MKRNB1500) || defined(ARDUINO_SAMD_MKRVIDOR4000) \
      || defined(ARDUINO_SAMD_CIRCUITPLAYGROUND_EXPRESS) || defined(__SAMD51__) || defined(__SAMD51J20A__) \
      || defined(__SAMD51J19A__) || defined(__SAMD51G19A__) || defined(__SAMD51P19A__)  \
      || defined(__SAMD21E15A__) || defined(__SAMD21E16A__) || defined(__SAMD21E17A__) || defined(__SAMD21E18A__) \
      || defined(__SAMD21G15A__) || defined(__SAMD21G16A__) || defined(__SAMD21G17A__) || defined(__SAMD21G18A__) \
      || defined(__SAMD21J15A__) || defined(__SAMD21J16A__) || defined(__SAMD21J17A__) || defined(__SAMD21J18A__) )
#error This code is designed to run on SAMD21/SAMD51 platform! Please check your Tools->Board setting.
#endif

/////////////////////////////////////////////////////////////////

// These define's must be placed at the beginning before #include "TimerInterrupt_Generic.h"
// _TIMERINTERRUPT_LOGLEVEL_ from 0 to 4
// Don't define _TIMERINTERRUPT_LOGLEVEL_ > 0. Only for special ISR debugging only. Can hang the system.
// Don't define TIMER_INTERRUPT_DEBUG > 2. Only for special ISR debugging only. Can hang the system.
#define TIMER_INTERRUPT_DEBUG         0
#define _TIMERINTERRUPT_LOGLEVEL_     0

// Select only one to be true for SAMD21. Must must be placed at the beginning before #include "TimerInterrupt_Generic.h"
#define USING_TIMER_TC3         true      // Only TC3 can be used for SAMD51
#define USING_TIMER_TC4         false     // Not to use with Servo library
#define USING_TIMER_TC5         false
#define USING_TIMER_TCC         false
#define USING_TIMER_TCC1        false
#define USING_TIMER_TCC2        false     // Don't use this, can crash on some boards

// Uncomment To test if conflict with Servo library
//#include "Servo.h"

/////////////////////////////////////////////////////////////////

// To be included only in main(), .ino with setup() to avoid `Multiple Definitions` Linker Error
#include "TimerInterrupt_Generic.h"

//#ifndef LED_BUILTIN
//  #define LED_BUILTIN       13
//#endif

#ifndef LED_BLUE
	#define LED_BLUE          2
#endif

#ifndef LED_RED
	#define LED_RED           8
#endif

unsigned int interruptPin = 7;

// TC3, TC4, TC5 max permissible TIMER_INTERVAL_MS is 1398.101 ms, larger will overflow, therefore not permitted
// Use TCC, TCC1, TCC2 for longer TIMER_INTERVAL_MS
#define TIMER_INTERVAL_MS          1
#define DEBOUNCING_INTERVAL_MS      80

#define LOCAL_DEBUG                 1

///////////////////////////////////////////////

#if (TIMER_INTERRUPT_USING_SAMD21)

	#if USING_TIMER_TC3
		#define SELECTED_TIMER      TIMER_TC3
	#elif USING_TIMER_TC4
		#define SELECTED_TIMER      TIMER_TC4
	#elif USING_TIMER_TC5
		#define SELECTED_TIMER      TIMER_TC5
	#elif USING_TIMER_TCC
		#define SELECTED_TIMER      TIMER_TCC
	#elif USING_TIMER_TCC1
		#define SELECTED_TIMER      TIMER_TCC1
	#elif USING_TIMER_TCC2
		#define SELECTED_TIMER      TIMER_TCC
	#else
		#error You have to select 1 Timer
	#endif

#else

	#if !(USING_TIMER_TC3)
		#error You must select TC3 for SAMD51
	#endif

	#define SELECTED_TIMER      TIMER_TC3

#endif

// Init selected SAMD timer
SAMDTimer ITimer(SELECTED_TIMER);

////////////////////////////////////////////////

volatile unsigned long rotationTime = 0;
float RPM       = 0.00;
float avgRPM    = 0.00;

volatile int debounceCounter;

volatile bool activeState = false;

void detectRotation()
{
	activeState = true;
}

void TimerHandler()
{
	if ( activeState )
	{
		// Reset to prepare for next round of interrupt
		activeState = false;

		if (debounceCounter >= DEBOUNCING_INTERVAL_MS / TIMER_INTERVAL_MS )
		{

			//min time between pulses has passed
			RPM = (float) ( 60000.0f / ( rotationTime * TIMER_INTERVAL_MS ) );

			avgRPM = ( 2 * avgRPM + RPM) / 3,

#if (TIMER_INTERRUPT_DEBUG > 1)
			Serial.print("RPM = ");
			Serial.print(avgRPM);
			Serial.print(", rotationTime ms = ");
			Serial.println(rotationTime * TIMER_INTERVAL_MS);
#endif

			rotationTime = 0;
			debounceCounter = 0;
		}
		else
			debounceCounter++;
	}
	else
	{
		debounceCounter++;
	}

	if (rotationTime >= 5000)
	{
		// If idle, set RPM to 0, don't increase rotationTime
		RPM = 0;

#if (TIMER_INTERRUPT_DEBUG > 1)
		Serial.print("RPM = ");
		Serial.print(RPM);
		Serial.print(", rotationTime = ");
		Serial.println(rotationTime);
#endif

		rotationTime = 0;
	}
	else
	{
		rotationTime++;
	}
}

void setup()
{
	pinMode(interruptPin, INPUT_PULLUP);

	Serial.begin(115200);

	while (!Serial && millis() < 5000);

	delay(100);

	Serial.print(F("\nStarting ISR_RPM_Measure on "));
	Serial.println(BOARD_NAME);
	Serial.println(SAMD_TIMER_INTERRUPT_VERSION);
	Serial.println(TIMER_INTERRUPT_GENERIC_VERSION);
	Serial.print(F("CPU Frequency = "));
	Serial.print(F_CPU / 1000000);
	Serial.println(F(" MHz"));

	// Interval in millisecs
	if (ITimer.attachInterruptInterval_MS(TIMER_INTERVAL_MS, TimerHandler))
	{
		Serial.print(F("Starting ITimer OK, millis() = "));
		Serial.println(millis());
	}
	else
		Serial.println(F("Can't set ITimer. Select another freq. or timer"));

	// Assumming the interruptPin will go LOW
	attachInterrupt(digitalPinToInterrupt(interruptPin), detectRotation, FALLING);
}

void loop()
{
}