[HELP] <title> Does not read data from the inverter axioma energy ismppt bf 3000 #185
Comments
|
What tells the webserial (or USB serial) from the ESP when No Data is recived? |
|
I used different boards based on 8266mod. also differences in TTL boards from different manufacturers There is a photo of a successful connection left If the connection is successful, the PI30 inverter protocol is determined connected with connectors, then switched to soldering. (Immediately after soldering there was the first success) Web Console v 2.2.0 pre.6 [WebSerial] Connecting... Web Console v 1.2.0 pre.4 [18:08:24] ----------------- End Autodetect ----------------- [18:08:24] MQTT Client State: 0 [18:08:24] ----------------- Start Autodetect ----------------- [18:08:26] [C: QPI][CR: 0][CC: 0][L: 3] [18:08:26] [18:08:26] QPI: NAK (Length: 3) [18:08:26] [18:08:28] [C: ^P005PI][CR: 0][CC: 0][L: 3] [18:08:28] [18:08:28] ^P005PI: NAK (Length: 3) [18:08:28] [18:08:28] Try Autodetect Protocol [18:08:28] [18:08:30] [C: QPI][CR: 0][CC: 0][L: 3] [18:08:30] [18:08:30] QPI: NAK (Length: 3) [18:08:30] [18:08:32] [C: ^P005PI][CR: 0][CC: 0][L: 3] [18:08:32] [18:08:32] ^P005PI: NAK (Length: 3) [18:08:32] [18:08:32] Try Autodetect Protocol [18:08:32] [18:08:34] [C: QPI][CR: 0][CC: 0][L: 3] [18:08:34] [18:08:34] QPI: NAK (Length: 3) [18:08:34] [18:08:36] [C: ^P005PI][CR: 0][CC: 0][L: 3] [18:08:36] [18:08:36] ^P005PI: NAK (Length: 3) [18:08:36] [18:08:37] Try Autodetect Modbus device [18:08:37] [18:08:38] Response Timed Out [18:08:38] [18:08:40] Response Timed Out [18:08:40] [18:08:40] Time-out [18:08:40] [18:08:40] Request failed! [18:08:41] [18:08:42] Response Timed Out [18:08:42] [18:08:44] Response Timed Out [18:08:44] [18:08:44] Time-out [18:08:44] [18:08:45] Request failed! [18:08:45] [18:08:46] Response Timed Out [18:08:46] [18:08:48] Response Timed Out [18:08:48] [18:08:48] Time-out [18:08:49] [18:08:49] Request failed! [18:08:49] [18:08:50] Response Timed Out [18:08:51] [18:08:52] Response Timed Out [18:08:52] [18:08:53] Time-out [18:08:53] [18:08:53] Request failed! [18:08:53] [18:08:53] ----------------- End Autodetect ----------------- POWER SUPPLY of boards from USB from a separate power supply unit or computer |
|
I have No Idea why it Work and dont Work later. |
|
Please tell me if it is possible to manually poll an unconnected inverter to check if it responds to requests.4 груд. 2024 р. о 00:46 Rocky ***@***.***> пише:
I have No Idea why it Work and dont Work later.
Looks Like a communication issue
—Reply to this email directly, view it on GitHub, or unsubscribe.You are receiving this because you authored the thread.Message ID: ***@***.***>
|
|
you can try to force a protocol by paste following in the webserial console setp x |
|
Still managed to start. Thanks! |
A clear and concise description of what the problem is.
Does not read data from the inverter axioma energy ismppt bf 3000.
Several times it was possible to get data in the Home Assistant, this confirms that the settings are correct. In this case, the Solar2MQTT_d1_mini_1.2.0-Pre4.bin firmware was used. The data was obtained 3 times for 2-3 hours. The rest of the time, either does not read anything at all or 0
Firmware changes do not help.
at the same time, wachpower receives data only if the version is older than version 1.1.9. i.e. 1.1.10 does not receive
Connecting with one wire to the TTL board and to the computer
Additional context
The text was updated successfully, but these errors were encountered: