-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathREADME.hardware
126 lines (93 loc) · 2.94 KB
/
README.hardware
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
i.MX7D Sabre Board Support Package
Table of Contents
=================
1. Supported Boards
2. Change History
3. BSP Features
4. BSP Notes
1. Supported Boards
===================
This BSP supports the following boards:
+ I.MX7D SABRE : Board: MCIMX7SABRE, SCH-28590 REVD1, 700-28590 REVD.
CPU: PCIMX7D rev1.2
2. Change History
=================
- 2024/12 (LINUXPG-2454): Wind River Linux10.24 RCPL04, support I.MX7D SABRE
based on FSL IMX SDK v6.6
3. BSP Features
===============
3.1 Supported Features
======================
This BSP supports the following features.
o Bus
+ I2C: On-Chip I2C controller
+ PCIe: On-Chip PCIe controller
+ SPI: Freescale ECSPI bus controller in master mode
o Network
+ Ethernet: FEC 10/100/1000 MAC ethernet controller, BCM54220B0KFBG external PHY
+ IEEE 1588: based on FEC controller
+ CAN: FLEXCAN, Flexible controller area network
+ WIFI: LBEH5HMZPC-TEMP
o USB
+ USB Host: 1 EHCI compatible host controller in the chip
+ USB OTG: On-Chip UTMI transceiver, high/full/low speed
o Storage
+ SD/MMC: On-Chip ultra secured digital host controller (uSDHC)
o User_Interface_Multimedia
+ AUDIO:
+ HDMI codec
+ WM8960 codec
+ HDMI: On-Chip HDMI controller
o Power Mgmt
+ Suspend to RAM
+ CPU Freq
+ Bus Freq
+ CPU idle
o Misc Devices
+ UART: On-Chip High-Speed UART
+ Watchdog: On-Chip H/W watchdog timer
+ GPIO: On-Chip general purpose Input/Output
+ RTC: On-Chip secure real time clock
+ Sensors: On-Chip temperature sensor
+ Power Regulator: ANATOP PMIC power regulator
+ SDMA: On-Chip smart direct memory access controller
+ PWM: Pulse width modulator
+ CAAM (security engine)
+ Accelerometer/Magnetometer: FXOS8700CQR1
+ Gyroscope: FXAS21002C
+ Barometer/Altimeter: MPL3115A2
3.2 Limited Supported Features
==============================
3.3 Unsupported Features
========================
The following features are not supported and not validated:
x ESAI card
x CortexM4
x MIPI-DSI Display
x MIPI-CSI CMOS sensor
x EPDC
x MikroBUS
x BT: LBEH5HMZPC-TEMP
4. BSP Notes
============
4.1 Hardware Description
------------------------
For complete hardware details please refer to the manual/PDF that should have
accompanied the board.
4.2 Target Notes
----------------
NOTE: This BSP is only validated in the following environment, if used in a
different environment it may run into unknown issues.
IMX7D SABRE:
CPU: Freescale i.MX7D rev1.2 1000 MHz (running at 792 MHz)
CPU: Commercial temperature grade (0C to 95C) at 41C
Model: Freescale i.MX7 SabreSD Board
Board: i.MX7D SABRESD RevA in secure mode
BootLoader Version: U-Boot 2024.04-lf_v2024.04+gde16f4f1+p0 (Sep 02 2024 - 10:44:35 +0000)
4.3 Specify boot medium
-----------------------
4.3.1 IMX7D SABRE (SCH-28590 REVD1, 700-28590 REVD)
---------------------------------------------------
1. Booting from SD card
Switch D1 D2 D3 D4 D5 D6 D7 D8
SW2 OFF OFF ON OFF OFF OFF ON OFF