fletcher-snap

Fletcher oc-accel platform support.

This platform has been derived from https://github.com/abs-tudelft/fletcher-snap, much like oc-accel is the successor of SNAP (SNAP = CAPI 1.0 and 2.0, ocxl aka. oc-accel is OpenCAPI 3.0).

As this repo contains only the needed platform support, the main fletcher library is needed for all the platform-agnostic parts (including VHDL code, common runtime library, example hardware and software code). That repo is included as a git submodule, but you can also check it out elsewhere yourself. In that case, you need to make sure that the FLETCHER_DIR, to be set in oc-accel/env.sh, points to it.

Platform-specific changes needed in fletcher itself (patch):

diff --git a/hardware/interconnect/BusReadBuffer.vhd b/hardware/interconnect/BusReadBuffer.vhd
index 976cbf5..dc55010 100644
--- a/hardware/interconnect/BusReadBuffer.vhd
+++ b/hardware/interconnect/BusReadBuffer.vhd
@@ -205,12 +205,12 @@ begin
           -- Check if the request burst length is not larger than the FIFO depth
           assert unsigned(ms_req_len) < 2**DEPTH_LOG2
             report "Violated burst length requirement. ms_req_len(=" & slvToUDec(ms_req_len) & ") < 2**DEPTH_LOG2(=" & integer'image(2**DEPTH_LOG2) & ") not met, deadlock!"
-            severity FAILURE;
+            severity WARNING;
 
           -- Check if either the amount of space reserved is larger than 0 or the fifo is ready
           assert reserved_v > 0 or fifo_ready = '1'
             report "Bus buffer deadlock!"
-            severity FAILURE;
+            severity WARNING;
 
           -- Check if the amount of space reserved is equal or larger than 0 after the reservation
           assert reserved_v >= 0
@@ -218,7 +218,7 @@ begin
                    "Check if BUS_LEN_WIDTH is wide enough to contain log2(slv_rreq_len)+2 bits. " &
                    "reserved_v=" & sgnToDec(reserved_v) & ">= 0. " &
                    "Reserved (if accepted):" & sgnToDec(reserved_if_accepted)
-            severity FAILURE;
+            severity WARNING;
 
           -- pragma translate_on

diff --git a/hardware/vhlib/stream/StreamPipelineControl.vhd b/stream/StreamPipelineControl.vhd
index 034643a..cefce8b 100644
--- a/hardware/vhlib/stream/StreamPipelineControl.vhd
+++ b/hardware/vhlib/stream/StreamPipelineControl.vhd
@@ -226,12 +226,12 @@ begin
         end if;
         if out_valid_s = '1' and out_ready = '1' then
             assert fifo_reserved_v > 0
-            report "FIFO underflow possible!" severity failure;
+            report "FIFO underflow possible!" severity warning;
             fifo_reserved_v := fifo_reserved_v - 1;
         end if;
         if pipe_valid_s(pipe_valid_s'HIGH) = '1' and pipe_delete = '1' then
             assert fifo_reserved_v > 0
-            report "FIFO underflow possible!" severity failure;
+            report "FIFO underflow possible!" severity warning;
             fifo_reserved_v := fifo_reserved_v - 1;
         end if;
         fifo_reserved <= fifo_reserved_v;

Important: When you wish to run one of the examples, you will need to run make in the corresponding example directory in the fletcher directory. In addition, you need to add the flag --axi to the fletchgen command in the hw Makefile. Otherwise, the AxiTop file is not generated and will remain a black box. This is not an error for oc-accel so it will crash (hang) the ocse simulation without notice.